How to Apply, Clean and Remove Skateboard Grip Tape

Related Articles

Disclosure: As an Amazon Associate, Longboard Expert earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.

To apply skateboard grip tape, peel off the backing, center the grip sticky-side down on the deck, press it down from the middle outward to avoid bubbles, then run a file around the deck’s edge to mark the outline and cut along it with a razor blade. Smooth the cut edges with a scrap of grip, and poke the truck bolt holes through from underneath with a screwdriver. To clean grip tape, rub it with a grip cleaner or sanding-belt eraser, or scrub gently with a toothbrush and a little soapy water.

What you need

  • A sheet of grip tape (longboards need a longer sheet)
  • A razor blade or utility knife
  • A file (or the shaft of a screwdriver) to mark the edge
  • A screwdriver or skate tool to poke bolt holes
  • Optional: a hair dryer to remove old grip

How to apply grip tape, step by step

  1. Peel the backing off the grip, and keep it.
  2. Line it up: hold the grip sticky side down and center it over the deck so it overhangs at both ends.
  3. Lay it lightly first so you can lift and adjust if it’s crooked.
  4. Press it down from the center out toward each end with the heel of your hand, slowly, to avoid air bubbles.
  5. Remove bubbles: lay the saved backing over the grip and press firmly with your fist along the board.
  6. Mark the outline: run a file firmly around the deck edge at a consistent angle to scratch a white line in the grip.
  7. Cut: with a razor blade, cut along the line in one long, steady cut, blade angled toward the deck. Cut away from your body.
  8. Smooth the edges by rubbing a scrap of grip along them.
  9. Poke the bolt holes: from underneath, push a screwdriver through each truck hole, then flip the board and push the bolts through.
  10. Mount your trucks and ride.

Steps based on evo’s guide to gripping a skateboard deck.

Skateboard grip tape on Amazon →  |  Longboard grip tape →

Tips for a clean grip job

  • Work on a clean, flat surface at room temperature; grip sticks better when it isn’t cold.
  • Use a fresh, sharp blade; dull blades tear the grip.
  • Want a design? Cut shapes or stripes before you press the grip down fully, or add art with paint pens first.
  • On longboards with drop-through cutouts, cut around the truck openings from underneath after gripping.

How to clean grip tape

  1. Dry clean first: rub a grip cleaner (grip gum) or a sanding-belt cleaner over the grip like an eraser to lift dirt.
  2. For heavy dirt: scrub gently with a toothbrush and a little water, with a drop of mild dish soap if needed.
  3. Use as little water as possible so it doesn’t soak into the wood, and let the board dry fully.
  4. Don’t scrub too hard: aggressive scrubbing knocks off the grit and reduces grip.

Cleaning tips from Concrete Wave’s grip tape guide.

How to remove old grip tape

  1. Warm the grip with a hair dryer or heat gun (or leave the board in the sun) to soften the glue.
  2. Lift one end with a razor and peel slowly, keeping the grip low to the deck.
  3. Remove leftover adhesive with an adhesive remover such as Goo Gone; stronger solvents can damage the deck’s finish.

Frequently asked questions

How long does grip tape last?

It depends on how much you ride. Replace it when it feels smooth and your shoes slip, usually when you change decks.

Can you reuse grip tape?

Not really. Once peeled, it loses stickiness and often tears.

Does grip tape need cleaning?

Occasionally. Clean grip keeps traction and looks better, but don’t over-clean.

Is longboard grip tape different?

It’s the same material in longer or wider sheets; some longboarders choose coarser grip for slides and downhill.

Sources: evo “How to Grip a Skateboard Deck”; Concrete Wave “How to Clean, Remove and Apply Grip Tape.”

More on this topic

Comments

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Popular stories