Disclosure: As an Amazon Associate, Longboard Expert earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.
Most hoverboards use a 36V lithium-ion battery and a 42V charger, often rated about 2 amps, with a round 3-prong plug. A full charge takes about 2 to 5 hours depending on the model. The safest charger is always the one that came with your board, or an exact replacement from the same brand for that model.
Quick answer
- Typical charger: 42V output for a 36V battery (42V is the full-charge voltage of a 36V lithium pack)
- Connector: most boards use a standard round 3-prong plug; some, such as many Hover-1 models, use a smaller “mini” 3-prong
- Charge time: about 2 to 5 hours (Jetson lists up to 3, 4 or 5 hours by model)
- Light colors: red usually means charging, green means full or not charging
- Safety: use the original charger and never charge unattended or overnight (CPSC)
Why a 36V hoverboard needs a 42V charger
A hoverboard’s battery is usually made of 10 lithium-ion cells in series. Each cell is about 3.6V nominal and 4.2V when full, so the pack is labeled 36V but charges up to 42V. That’s why the charger label says 42V. A charger with a different voltage, or one made for a different battery chemistry, can damage the battery or cause it to overheat.
| Battery label | Charger output | Where you’ll see it |
|---|---|---|
| 36V | 42V | Most standard and kids’ hoverboards |
| Other voltages | Check the label | Some larger or off-road boards; always match the manufacturer’s spec |
Look at the label on your original charger and the sticker on the board or battery before buying anything. Match voltage, connector and polarity; the amp rating should not exceed what the manufacturer specifies.
Hoverboard charger connectors
- Standard 3-prong round plug: the most common hoverboard connector.
- Mini 3-prong: looks the same but is noticeably smaller in diameter. Many Hover-1 boards (Beast, Eclipse, H1, Horizon, Nomad, Titan and Ultra) use this type.
- Barrel (DC) plugs: used by some brands and scooters. Check the inner and outer diameter and the polarity.
A plug that fits isn’t proof a charger is right. Two chargers with the same plug can have different voltages.
How long does it take to charge a hoverboard?
| Example | Charge time (up to) |
|---|---|
| Jetson Flash, Impact, Rave, Spin, Strike, Sphere and others | 3 hours |
| Jetson Alpha, Sync | 4 hours |
| Jetson Dash, Lumino, Magma, Prism, Zone and others | 5 hours |
| Gotrax Edge | About 5 hours |
Charge times from Jetson’s support page and retailer listings. Check your manual for your exact model.
Charge the board fully before the first ride (Jetson recommends 4 hours for the V6-XL, for example), then unplug it once the light turns green. To get more riding from each charge, see how long a hoverboard battery lasts.
What do the charger lights mean?
| Light | Usually means |
|---|---|
| Red | Charging |
| Green | Fully charged, or the charger isn’t connected to the board |
| Green right after plugging in | Battery already full, a bad connection, or the charger was plugged into the board before the wall |
| No light | No power from the outlet, a failed charger, or a damaged charging port |
Some models differ (Jetson’s Hali X flashes green while charging), so check the manual.
How to charge a hoverboard safely
- Use the original charger or an exact replacement for your model. The CPSC advises using only the charger that came with the board.
- Turn the board off before charging.
- Plug the charger into the wall first, then into the board. Jetson notes that doing it the other way can make the light show green when the battery isn’t full.
- Stay nearby. Don’t charge it while you’re asleep or away, and don’t leave it plugged in overnight. See can you leave a hoverboard charging overnight?
- Charge on a hard surface, away from beds, sofas, curtains and anything flammable.
- Unplug when it turns green.
- Let a hot board cool after riding before you plug it in.
Stop using the board and contact the manufacturer if the battery smells strange, gets very hot, swells, leaks or makes popping sounds. Hoverboards should be certified to UL 2272; a UL-listed charger on its own doesn’t make the whole board compliant. See hoverboards that won’t catch fire.
Can you use a universal hoverboard charger?
It’s best not to. Generic “universal” chargers may have the right plug but the wrong voltage, current or protections for your battery, and a CPSC commissioner has publicly warned against universal chargers for e-bike batteries because of fire risk. The same logic applies to hoverboard batteries. If you’ve lost the original, buy a replacement from the board’s manufacturer, or one listed for your exact model with matching voltage and connector. A replacement charger usually costs about $18 to $35 (Razor lists about $33 for the Hovertrax 2.0 charger).
See hoverboard chargers on Amazon → (check the voltage and connector match your board)
Hoverboard won’t charge? Quick checks
- Try a different wall outlet.
- Check the charging port for dirt, bent pins or looseness.
- Check the charger cable and plug for damage.
- If the light stays green but the board won’t turn on, the battery may be worn out or damaged.
- If the board won’t balance after a battery or charger issue, try calibrating the hoverboard.
For more fixes, see our hoverboard troubleshooting guide.
Frequently asked questions
What charger does a hoverboard use?
Most use a 42V charger for a 36V lithium-ion battery, with a round 3-prong plug. Check the label on your original charger to be sure.
Can I charge my hoverboard with a phone or laptop charger?
No. Phone and laptop chargers deliver far less voltage and use different connectors. Use the hoverboard’s own charger.
How do I know when my hoverboard is fully charged?
On most chargers the light turns from red to green. Some boards also show battery level with lights on the board.
Is it bad to leave a hoverboard plugged in?
Yes. Manufacturers such as Jetson say not to leave it plugged in overnight or for long periods, and the CPSC advises never charging unattended.
How should I store a hoverboard for winter?
Jetson recommends charging it fully before storage and topping it up about once a month. Store it indoors at room temperature.
Sources: US Consumer Product Safety Commission hoverboard safety alert; Jetson support (“How to charge my hoverboard”) and Jetson V6-XL manual; Monster Scooter Parts (Hover-1 mini 3-prong charger); iFixit Hover-1 charger troubleshooting; Razor parts pricing. Always follow your board’s manual.
