How to Calibrate a Hoverboard (Step by Step, by Brand)

Related Articles

Disclosure: As an Amazon Associate, Longboard Expert earns from qualifying purchases. If you buy through links on this page, we may earn a small commission at no extra cost to you.

To calibrate a hoverboard, turn it off, set it on a flat, level surface, make both foot pads level, then press and hold the power button until the lights flash or it beeps, and turn it off and on again. How long you hold the button depends on the brand: about 3 to 5 seconds on most Jetson boards, 10 seconds on Gotrax, and 15 to 20 seconds on the Razor Hovertrax 2.0. Calibration resets the gyroscope sensors so the board balances properly again.

When does a hoverboard need calibrating?

  • It won’t stay level, tilts, or rolls on its own when switched on
  • It turns faster in one direction than the other, or spins in circles
  • It beeps continuously or shows a flashing red light
  • It vibrates or feels uneven to ride
  • After a fall, after the battery ran completely flat, or after a repair

How to calibrate a hoverboard (general method)

  1. Turn the hoverboard off using its own power button.
  2. Place it on a flat, level, hard surface such as a garage floor or table. Don’t calibrate on carpet or a slope.
  3. Level the foot pads by hand so both sides sit parallel to the floor.
  4. Keep your weight off the board.
  5. Press and hold the power button until the lights flash and/or the board beeps (see brand times below).
  6. Release, then turn it off to lock in the calibration.
  7. Turn it back on and check that it stays level. Repeat up to two or three times if needed.

Calibration by brand

Brand / model Hold the power button Notes
Razor Hovertrax 2.0 / DLX 2.0 About 15 to 20 seconds (with the board on) Level the platforms first, turn power on and hold until it beeps and the lights flash, then turn off
Jetson (most models) 3 to 5 seconds Jetson Sphere: 15 seconds. Boards with voice say “calibration successful”; repeat up to 3 times
Gotrax 10 seconds LEDs flash; then press power to turn off and on
Hover-1 About 5 seconds Lights flash and the board confirms calibration
Boards with an app Use the app’s calibrate option Follow the on-screen steps carefully

From each manufacturer’s instructions (Razor, Jetson, Gotrax) and iFixit’s Hover-1 guide. Check your own manual, as steps can vary between models.

After calibrating: test it safely

  • Turn it on and confirm no red lights are flashing and both pads sit level.
  • Wear a helmet, then ride slowly on smooth, flat ground.
  • Turn gently in both directions and ride a small circle to check it responds evenly.

Still not working after calibration?

If the board still tilts, beeps or won’t respond after three attempts, the cause is likely a low or worn battery, a loose connector or a faulty sensor (gyro) board. Work through our hoverboard troubleshooting guide, or contact the manufacturer if the board is under warranty.

Frequently asked questions

How long does it take to calibrate a hoverboard?

Usually under a minute: a few seconds to hold the button, plus turning the board off and on.

Is resetting a hoverboard the same as calibrating it?

For most boards, yes: “reset” usually means recalibrating the balance sensors with the power-button method above.

Why does my hoverboard keep losing calibration?

Frequent falls, storing it tilted, running the battery completely flat, or a failing sensor board. If calibration doesn’t last, inspect the sensor boards and battery.

Can calibrating damage my hoverboard?

The power-button method is safe. eRideHero warns that resetting through Bluetooth apps should be done carefully and only when needed.

Sources: Razor Hovertrax 2.0/DLX 2.0 calibration instructions, Jetson support article on recalibration, Gotrax hoverboard guide, iFixit Hover-1 H1 troubleshooting, eRideHero calibration guide.

More on this topic

Comments

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Popular stories